Trova messaggi
Grasp these two points for the screw combination

Continuing with the previous topic, we will talk about screw combination in this section. In fact, for nylon toughening modification, compared with nylon fiber reinforcement or nylon flame retardant reinforcement, its requirements for screw combination are relatively simple.
But we want to emphasize two points
The first point
the aspect ratio of the twin-screw extruder used for nylon toughening modification should be longer, and it is recommended to be 44:1.

What is the benefit of a longer length-to-diameter ratio, that is, when the total cutout blocks are designed and the total number remains unchanged, if the length-to-diameter ratio is relatively long, it is conducive to the comparison of dispersing the combination of the cutout blocks Open, avoid 5 to 6 or more cutouts strung together.

As a result, the local resistance is very large, and then excessive shear heat is generated in this area, thereby destroying the performance of the material.

Second point

For nylon toughening, the screw combination should achieve the best effect on it, which is good dispersion and plasticization, and at the same time, the shear should be lower, that is, low shear.
So how to do it, first of all, we must grasp one point, that is, try not to use such high-shear threaded elements with a thickness of 90 degrees, or some threaded elements with reverse shear and relatively large resistance.

Then I usually recommend to use a small angle, and then combine the threaded elements with relatively thin slices, so that the shearing is relatively low while ensuring sufficient plasticization and dispersion, so the performance of the entire nylon after processing is greatly improved. It will be better to keep.

There is still a lot about the combination of this screw, let’s get to know it together in the next section.

The first point

the aspect ratio of the twin-screw extruder used for nylon toughening modification should be longer, and it is recommended to be 44:1.

What is the benefit of a longer length-to-diameter ratio, that is, when the total cutout blocks are designed and the total number remains unchanged, if the length-to-diameter ratio is relatively long, it is conducive to the comparison of dispersing the combination of the cutout blocks Open, avoid 5 to 6 or more cutouts strung together.

As a result, the local resistance is very large, and then excessive shear heat is generated in this area, thereby destroying the performance of the material.

Second point

For nylon toughening, the screw combination should achieve the best effect on it, which is good dispersion and plasticization, and at the same time, the shear should be lower, that is, low shear.

So how to do it, first of all, we must grasp one point, that is, try not to use such high-shear threaded elements with a thickness of 90 degrees, or some threaded elements with reverse shear and relatively large resistance.

Then I usually recommend to use a small angle, and then combine the threaded elements with relatively thin slices, so that the shearing is relatively low while ensuring sufficient plasticization and dispersion, so the performance of the entire nylon after processing is greatly improved. It will be better to keep.

There is still a lot about the combination of this screw, let’s get to know it together in the next sectio.

recente articoli

Come scegliere l'anidride maleica innestata POE appropriata per migliorare la tenacità del nylon?

Progettato appositamente per essere un moderatore d'urto per PA6, PA66 e sistemi poliammidici che necessitano di rinforzo e riempimento, Coace® W1A-F è la scelta perfetta per gli impieghi in cui una maggiore resistenza agli urti e tenacità sono fondamentali.

Per saperne di più →

Nuova svolta nella modifica del PBT: applicazione rivoluzionaria dell'agente indurente POE-g-GMA

L'uso dell'agente indurente POE-g-GMA nella modifica del PBT non solo risolve la fragilità del materiale PBT, ma fornisce anche nuove indicazioni per lo sviluppo dell'industria plastica.

Per saperne di più →

Quando si aggiungono cariche ai materiali compositi PP/PE, è necessario aggiungere un compatibilizzante?

Se si vuole approfondire l'uso dei compatibilizzanti PP-g-MAH, è possibile contattare un fornitore di prodotti chimici professionale per ottenere campioni e supporto tecnico. Il dialogo con COACE aiuta a personalizzare le miscele per soddisfare determinate esigenze applicative.

Per saperne di più →

LASCIATECI UN MESSAGGIO